思科1811w路由问题

我有一个思科1811w，我只是想现在得到一个基本的configuration。我在fa0上使用有线networking（TWC）（现在只是定期的内部dhcp，还没有完成桥接）和fa1作为内部10.0.0.0/24

连接到fa1的电脑确实得到了dhcp和路由器的设置，但是无论是在PC上还是在路由器上都不能ping通。不知道我在做什么错。

路由器内部的pingtesting：

Router#ping 8.8.8.8 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds: ..... Success rate is 0 percent (0/5)

IP信息：

 FastEthernet0 192.168.0.5 YES DHCP up up FastEthernet1 10.0.0.1 YES NVRAM up down (nothing plugged into 1 at the moment)

运行configuration：

 Current configuration : 1758 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! enable secret 5 $1$NMgE$p0dWLAM1aVTRcqnrIL2Vu1 ! no aaa new-model ! ! dot11 syslog ! ! ip cef no ip dhcp use vrf connectedip dhcp excluded-address 10.0.0.1 10.0.0.10 ! ip dhcp pool Lan1DHCP import all network 10.0.0.0 255.255.255.0 default-router 10.0.0.1 dns-server 10.0.0.1 8.8.8.8 8.8.4.4 ! ! ! multilink bundle-name authenticated ! ! ! ! archive log config hidekeys ! ! ! ! ! interface Dot11Radio0 no ip address shutdown speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio1 no ip address shutdown speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0 station-role root ! interface FastEthernet0 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet1 ip address 10.0.0.1 255.255.255.0 ip nat inside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet2 ! interface FastEthernet3 ! interface FastEthernet4 ! interface FastEthernet5 ! interface FastEthernet6 ! interface FastEthernet7 ! interface FastEthernet8 ! interface FastEthernet9 ! interface Vlan1 no ip address ! interface Async1 no ip address encapsulation slip ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 FastEthernet0 ! ! no ip http server no ip http secure-server ip nat inside source list 101 interface FastEthernet0 overload ! access-list 101 permit ip 10.0.0.0 0.0.0.255 any

@MarkoPolo是对的。有默认网关的问题。但我认为你应该使用默认网关，思科可以通过DHCP从ISP获得：

 ip route 0.0.0.0 0.0.0.0 dhcp

如果它能帮助别人，我的configuration是：

version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! enable secret 5 $1$XweJ$NMtNuu/R4emfBU0rpjamg1 ! no aaa new-model ! ! dot11 syslog ! ! ip cef no ip dhcp use vrf connected ip dhcp excluded-address 10.0.0.1 10.0.0.10 ! ip dhcp pool Lan1DHCP import all network 10.0.0.0 255.255.255.0 default-router 10.0.0.1 dns-server 8.8.8.8 8.8.4.4 ! ! ! multilink bundle-name authenticated ! ! ! ! archive log config hidekeys ! ! ! ! ! interface Dot11Radio0 no ip address shutdown speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio1 no ip address shutdown speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0 station-role root ! interface FastEthernet0 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet1 ip address 10.0.0.1 255.255.255.0 ip nat inside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet2 ! interface FastEthernet3 ! interface FastEthernet4 ! interface FastEthernet5 ! interface FastEthernet6 ! interface FastEthernet7 ! interface FastEthernet8 ! interface FastEthernet9 ! interface Vlan1 no ip address ! interface Async1 no ip address encapsulation slip ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 dhcp ! ! no ip http server no ip http secure-server ip nat inside source list 101 interface FastEthernet0 overload ! access-list 101 permit ip 10.0.0.0 0.0.0.255 any ! ! ! ! ! ! control-plane ! ! line con 0 line 1 modem InOut stopbits 1 speed 115200 flowcontrol hardware line aux 0 line vty 0 4 login ! end