我正在尝试使用OpenWRT（BARREER BREAKER（14.07，r42625））和Nodogsplash在TL-MR3020上创build一个强制门户。 我用ExtRoot增加了存储空间。
这是我的configuration文件：
的/ etc /configuration/ DHCP
config dnsmasq option domainneeded '1' option boguspriv '1' option filterwin2k '0' option localise_queries '1' option rebind_protection '1' option rebind_localhost '1' option local '/lan/' option domain 'lan' option expandhosts '1' option nonegcache '0' option authoritative '1' option readethers '1' option leasefile '/tmp/dhcp.leases' option resolvfile '/tmp/resolv.conf.auto' config dhcp 'lan' option interface 'lan' option start '100' option limit '150' option leasetime '12h' option dhcpv6 'server' option ra 'server' config dhcp 'wan' option interface 'wan' option ignore '1' config odhcpd 'odhcpd' option maindhcp '0' option leasefile '/tmp/hosts/odhcpd' option leasetrigger '/usr/sbin/odhcpd-update' config 'dhcp' option interface 'wifi' option start 100 option limit 150 option leasetime 2h 的/ etc /configuration/networking
config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config globals 'globals' option ula_prefix 'fda9:8510:6ea4::/48' config interface 'lan' option type 'bridge' option _orig_ifname 'eth0 radio0.network1' option _orig_bridge 'true' option proto 'dhcp' option ifname 'eth0' config interface 'wifi' option proto 'static' option ipaddr '10.10.15.1' option netmask '255.255.255.0' option _orig_ifname 'wlan0' option _orig_bridge 'false' option type 'bridge' option macaddr 'AD:2A:DD:FB:B3:64'
的/ etc /configuration/无线
config wifi-device 'radio0' option type 'mac80211' option channel '7' option hwmode '11g' option path 'platform/ar933x_wmac' option htmode 'HT20' option disabled '0' config wifi-iface option device 'radio0' option mode 'ap' option ssid 'Hotspot' option encryption 'none' option network 'wifi'
/etc/nodogsplash/nodogsplash.conf
# # Nodogsplash Configuration File # # Parameter: GatewayInterface # Default: NONE # # GatewayInterface is not autodetected, has no default, and must be set here. # Set GatewayInterface to the interface on your router # that is to be managed by Nodogsplash. # Typically br0 for the wired and wireless lan on OpenWrt White Russian. # May be br-lan on OpenWrt Kamikaze. # GatewayInterface br-wifi # FirewallRuleSet: authenticated-users # # Control access for users after authentication. # These rules are inserted at the beginning of the # FORWARD chain of the router's filter table, and # apply to packets that have come in to the router # over the GatewayInterface from MAC addresses that # have authenticated with Nodogsplash, and that are # destined to be routed through the router. The rules are # considered in order, and the first rule that matches # a packet applies to it. # If there are any rules in this ruleset, an authenticated # packet that does not match any rule is rejected. # NB: This ruleset is completely independent of # the preauthenticated-users ruleset. # FirewallRuleSet authenticated-users { # You may want to open access to a machine on a local # subnet that is otherwise blocked (for example, to # serve a redirect page; see RedirectURL). If so, # allow that explicitly here, eg: # FirewallRule allow tcp port 80 to 192.168.254.254 # Your router may have several interfaces, and you # probably want to keep them private from the GatewayInterface. # If so, you should block the entire subnets on those interfaces, eg: FirewallRule block to 192.168.0.0/16 FirewallRule block to 10.0.0.0/8 # Typical ports you will probably want to open up include # 53 udp and tcp for DNS, # 80 for http, # 443 for https, # 22 for ssh: FirewallRule allow tcp port 53 FirewallRule allow udp port 53 FirewallRule allow tcp port 80 FirewallRule allow tcp port 443 FirewallRule allow tcp port 22 } # end FirewallRuleSet authenticated-users # FirewallRuleSet: preauthenticated-users # # Control access for users before authentication. # These rules are inserted in the PREROUTING chain # of the router's nat table, and in the # FORWARD chain of the router's filter table. # These rules apply to packets that have come in to the # router over the GatewayInterface from MAC addresses that # are not on the BlockedMACList or TrustedMACList, # are *not* authenticated with Nodogsplash. The rules are # considered in order, and the first rule that matches # a packet applies to it. A packet that does not match # any rule here is rejected. # NB: This ruleset is completely independent of # the authenticated-users and users-to-router rulesets. # FirewallRuleSet preauthenticated-users { # For preauthenticated users to resolve IP addresses in their initial # request not using the router itself as a DNS server, # you probably want to allow port 53 udp and tcp for DNS. FirewallRule allow tcp port 53 FirewallRule allow udp port 53 # For splash page content not hosted on the router, you # will want to allow port 80 tcp to the remote host here. # Doing so circumvents the usual capture and redirect of # any port 80 request to this remote host. # Note that the remote host's numerical IP address must be known # and used here. # FirewallRule allow tcp port 80 to 123.321.123.321 } # end FirewallRuleSet preauthenticated-users # FirewallRuleSet: users-to-router # # Control access to the router itself from the GatewayInterface. # These rules are inserted at the beginning of the # INPUT chain of the router's filter table, and # apply to packets that have come in to the router # over the GatewayInterface from MAC addresses that # are not on the TrustedMACList, and are destined for # the router itself. The rules are # considered in order, and the first rule that matches # a packet applies to it. # If there are any rules in this ruleset, a # packet that does not match any rule is rejected. # FirewallRuleSet users-to-router { # Nodogsplash automatically allows tcp to GatewayPort, # at GatewayAddress, to serve the splash page. # However you may want to open up other ports, eg # 53 for DNS and 67 for DHCP if the router itself is # providing these services. FirewallRule allow udp port 53 FirewallRule allow tcp port 53 FirewallRule allow udp port 67 # You may want to allow ssh, http, and https to the router # for administration from the GatewayInterface. If not, # comment these out. FirewallRule allow tcp port 22 FirewallRule allow tcp port 80 FirewallRule allow tcp port 443 } # end FirewallRuleSet users-to-router # EmptyRuleSetPolicy directives # The FirewallRuleSets that NoDogSplash permits are: # # authenticated-users # preauthenticated-users # users-to-router # trusted-users # trusted-users-to-router # # For each of these, an EmptyRuleSetPolicy can be specified. # An EmptyRuleSet policy applies to a FirewallRuleSet if the # FirewallRuleSet is missing from this configuration file, # or if it exists but contains no FirewallRules. # # The possible values of an EmptyRuleSetPolicy are: # allow -- packets are accepted # block -- packets are rejected # passthrough -- packets are passed through to pre-existing firewall rules # # Default EmptyRuleSetPolicies are set as follows: # EmptyRuleSetPolicy authenticated-users passthrough # EmptyRuleSetPolicy preauthenticated-users block # EmptyRuleSetPolicy users-to-router block # EmptyRuleSetPolicy trusted-users allow # EmptyRuleSetPolicy trusted-users-to-router allow # Parameter: GatewayName # Default: NoDogSplash # # Set GatewayName to the name of your gateway. This value # will be available as variable $gatewayname in the splash page source # and in status output from ndsctl, but otherwise doesn't matter. # If none is supplied, the value "NoDogSplash" is used. # # GatewayName NoDogSplash # Parameter: GatewayAddress # Default: Discovered from GatewayInterface # # This should be autodetected on an OpenWRT system, but if not: # Set GatewayAddress to the IP address of the router on # the GatewayInterface. This is the address that the Nodogsplash # server listens on. # # GatewayAddress 192.168.1.1 # Parameter: ExternalInterface # Default: Autodetected from /proc/net/route # # This should be autodetected on a OpenWRT system, but if not: # Set ExtrnalInterface to the 'external' interface on your router, # ie the one which provides the default route to the internet. # Typically vlan1 for OpenWRT. # ExternalInterface br-lan #br-lan # Parameter: RedirectURL # Default: none # # After authentication, normally a user is redirected # to their initially requested page. # If RedirectURL is set, the user is redirected to this URL instead. # # RedirectURL http://www.ilesansfil.org/ # Parameter: GatewayPort # Default: 2050 # # Nodogsplash's own http server uses GatewayAddress as its IP address. # The port it listens to at that IP can be set here; default is 2050. # # GatewayPort 2050 # Parameter: MaxClients # Default: 20 # # Set MaxClients to the maximum number of users allowed to # connect at any time. (Does not include users on the TrustedMACList, # who do not authenticate.) # # MaxClients 20 # ClientIdleTimeout # Parameter: ClientIdleTimeout # Default: 10 # # Set ClientIdleTimeout to the desired of number of minutes # of inactivity before a user is automatically 'deauthenticated'. # # ClientIdleTimeout 10 # Parameter: ClientForceTimeout # Default: 360 # # Set ClientForceTimeout to the desired number of minutes before # a user is automatically 'deauthenticated', whether active or not # # ClientForceTimeout 360 # Parameter: AuthenticateImmediately # Default: no # # Set to yes (or true or 1), to immediately authenticate users # who make a http port 80 request on the GatewayInterface (that is, # do not serve a splash page, just redirect to the user's request, # or to RedirectURL if set). # # AuthenticateImmediately no # Parameter: MACMechanism # Default: block # # Either block or allow. # If 'block', MAC addresses on BlockedMACList are blocked from # authenticating, and all others are allowed. # If 'allow', MAC addresses on AllowedMACList are allowed to # authenticate, and all other (non-trusted) MAC's are blocked. # # MACMechanism block # Parameter: BlockedMACList # Default: none # # Comma-separated list of MAC addresses who will be completely blocked # from the GatewayInterface. Ignored if MACMechanism is allow. # NB: weak security, since MAC addresses are easy to spoof. # # BlockedMACList 00:00:DE:AD:BE:EF,00:00:C0:1D:F0:0D # Parameter: AllowedMACList # Default: none # # Comma-separated list of MAC addresses who will not be completely # blocked from the GatewayInterface. Ignored if MACMechanism is block. # NB: weak security, since MAC addresses are easy to spoof. # # AllowedMACList 00:00:12:34:56:78 # Parameter: TrustedMACList # Default: none # # Comma-separated list of MAC addresses who are not subject to # authentication, and are not restricted by any FirewallRuleSet. # NB: weak security, since MAC addresses are easy to spoof. # # TrustedMACList 00:00:CA:FE:BA:BE, 00:00:C0:01:D0:0D # Parameter: PasswordAuthentication # Default: no # Set to yes (or true or 1), to require a password matching # the Password parameter to be supplied when authenticating. # # # PasswordAuthentication no # Parameter: Password # Default: none # Whitespace delimited string that is compared to user-supplied # password when authenticating. # # # Password nodog # Parameter: UsernameAuthentication # Default: no # Set to yes (or true or 1), to require a username matching # the Username parameter to be supplied when authenticating. # # # UsernameAuthentication no # Parameter: Username # Default: none # Whitespace delimited string that is compared to user-supplied # username when authenticating. # # # Username guest # Parameter: PasswordAttempts # Default: 5 # Integer number of failed password/username entries before # a user is forced to reauthenticate. # # # PasswordAttempts 5 # Parameter: TrafficControl # Default: no # # Set to yes (or true or 1), to enable traffic control in Nodogsplash. # # TrafficControl no # Parameter: DownloadLimit # Default: 0 # # If TrafficControl is enabled, this sets the maximum download # speed to the GatewayInterface, in kilobits per second. # For example if you have an ADSL connection with 768 kbit # download speed, and you want to allow about half of that # bandwidth for the GatewayInterface, set this to 384. # A value of 0 means no download limiting is done. # # DownloadLimit 384 # Parameter: UploadLimit # Default: 0 # # If TrafficControl is enabled, this sets the maximum upload # speed from the GatewayInterface, in kilobits per second. # For example if you have an ADSL connection with 128 kbit # upload speed, and you want to allow about half of that # bandwidth for the GatewayInterface, set this to 64. # A value of 0 means no upload limiting is done. # # UploadLimit 64 # Parameter: GatewayIPRange # Default: 0.0.0.0/0 # # By setting this parameter, you can specify a range of IP addresses # on the GatewayInterface that will be responded to and managed by # Nodogsplash. Addresses outside this range do not have their packets # touched by Nodogsplash at all. # Defaults to 0.0.0.0/0, that is, all addresses. # # GatewayIPRange 0.0.0.0/0 # Parameter: ImagesDir # Default: images # # Set the directory from which images are served. # Use $imagesdir in HTML files to reference this directory. # # ImagesDir images # Parameter: BinVoucher # Default: None # # Enable Voucher Support. # If set, an alphanumeric voucher HTTP parameter is accepted # and passed to a command line call along with the clients MAC: # # $<BinVoucher> auth_voucher <mac> <voucher> # # BinVoucher must point to a program that will be called as described above. # The call is expected to output the number of seconds the client # is to be authenticated. Zero or negative seconds will cause the # authentification request to be rejected. # The output may contain a user specific download and upload limit in KBit/s: # <seconds> <download> <upload> # # BinVoucher "/bin/myauth" # Parameter: ForceVoucher # Default: no # # Force the use of a voucher. Authentification is not possible without voucher. # # ForceVoucher no # Parameter: EnablePreAuth # Default: no # # Enable pre-authentication support. # Pass the MAC of a client to a command line call before the splash page # would be send: # # $<BinVoucher> auth_status <mac> # # The call is expected to output the number of seconds the client # is to be authenticated. Zero or negative seconds will cause the # splash page to be displayed. # The output may contain a user specific download and upload limit in KBit/s: # <seconds> <download> <upload> # # EnablePreAuth no
dmesg的
[ 26.430000] IPv6: ADDRCONF(NETDEV_CHANGE): wifi: link becomes ready [ 26.460000] IPv6: ADDRCONF(NETDEV_CHANGE): br-wifi: link becomes ready [ 27.260000] br-lan: port 1(eth0) entered forwarding state [ 28.420000] wifi: port 1(br-wifi) entered forwarding state
iptables -t nat -L
Chain PREROUTING (policy ACCEPT) target prot opt source destination ndsOUT all -- anywhere anywhere Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination Chain ndsOUT (1 references) target prot opt source destination ACCEPT all -- anywhere anywhere mark match 0x200/0x700 ACCEPT all -- anywhere anywhere mark match 0x400/0x700 ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:domain DNAT tcp -- anywhere anywhere tcp dpt:www to:10.10.15.1:2050 ACCEPT all -- anywhere anywhere
iptables -t filter -L
Chain INPUT (policy ACCEPT) target prot opt source destination ndsRTR all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ndsNET all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain ndsAUT (1 references) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED REJECT all -- anywhere 192.168.0.0/16 reject-with icmp-port-unreachable REJECT all -- anywhere 10.0.0.0/8 reject-with icmp-port-unreachable ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:www ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- anywhere anywhere tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain ndsNET (1 references) target prot opt source destination DROP all -- anywhere anywhere mark match 0x100/0x700 DROP all -- anywhere anywhere state INVALID TCPMSS tcp -- anywhere anywhere tcp flags:SYN,RST/SYN TCPMSS clamp to PMTU ACCEPT all -- anywhere anywhere mark match 0x200/0x700 ndsAUT all -- anywhere anywhere mark match 0x400/0x700 ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:domain REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain ndsRTR (1 references) target prot opt source destination DROP all -- anywhere anywhere mark match 0x100/0x700 DROP all -- anywhere anywhere state INVALID ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED DROP tcp -- anywhere anywhere tcp option=!2 flags:SYN/SYN ACCEPT tcp -- anywhere anywhere tcp dpt:2050 ACCEPT all -- anywhere anywhere mark match 0x200/0x700 ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:ssh ACCEPT tcp -- anywhere anywhere tcp dpt:www ACCEPT tcp -- anywhere anywhere tcp dpt:https REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain ndsTRT (0 references) target prot opt source destination Chain ndsTRU (0 references) target prot opt source destination
我可以： – 连接到AP – 获取IP地址 – 获取启animation面 – 通过WiFi连接到openwrt接口 – DNSstream量正常工作
我不能： – 使用任何其他stream量
我试过： – 做一个远程tcpdump。 从wifi到eth0的包无损。 没有回应的要求。 – 我试图为Nodogsplash添加规则，以允许未经过身份validation的设备使用http和httpsstream量。 没有不同
你看到有什么问题吗？