我需要连接6 nic到一个单一的债券，而在RHEL5.4上，其中2个是Broadcom，另外4个是Intel。 两个问题请：
1.该configuration是否可行，交换机和nics上的先决条件/configuration是什么？
2.configuration完这个绑定后，在/ proc / net / bonding / bond0（下面）中查看绑定中的6个eth设备。 但是其中只有两个具有聚合器ID，因此只显示两个端口。 这是什么意思？ 这是正常的吗？
# cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.4.0 (October 7, 2008) Bonding Mode: IEEE 802.3ad Dynamic link aggregation<br> Transmit Hash Policy: layer2 (0)<br> MII Status: up<br> MII Polling Interval (ms): 150<br> Up Delay (ms): 0<br> Down Delay (ms): 0<br> 802.3ad info<br> LACP rate: slow<br> Active Aggregator Info:<br> Aggregator ID: 13<br> Number of ports: 2<br> Actor Key: 9<br> Partner Key: 17<br> Partner Mac Address: 00:01:81:28:84:00<br> Slave Interface: eth0<br> MII Status: up<br> Link Failure Count: 0<br> Permanent HW addr: 00:26:b9:49:ed:45<br> Aggregator ID: 13<br> Slave Interface: eth1<br> MII Status: up<br> Link Failure Count: 1<br> Permanent HW addr: 00:26:b9:49:ed:47<br> Aggregator ID: 13<br> Slave Interface: eth4<br> MII Status: up<br> Link Failure Count: 0<br> Permanent HW addr: 00:1b:21:4a:79:58<br> Aggregator ID: 15<br> Slave Interface: eth5<br> MII Status: up<br> Link Failure Count: 0<br> Permanent HW addr: 00:1b:21:4a:79:59<br> Aggregator ID: 14<br> Slave Interface: eth8<br> MII Status: up<br> Link Failure Count: 0<br> Permanent HW addr: 00:1b:21:4a:77:b0<br> Aggregator ID: 17<br> Slave Interface: eth9<br> MII Status: up<br> Link Failure Count: 0<br> Permanent HW addr: 00:1b:21:4a:77:b1<br> Aggregator ID: 18<br> 谢谢，mku。
评论后：
#ifconfig: bond1 Link encap:Ethernet HWaddr 00:26:B9:49:ED:45 <br> inet6 addr: fe80::226:b9ff:fe49:ed45/64 Scope:Link<br> UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1<br> RX packets:519 errors:0 dropped:0 overruns:0 frame:0<br> TX packets:743 errors:0 dropped:0 overruns:0 carrier:0<br> collisions:0 txqueuelen:0 <br> RX bytes:52812 (51.5 KiB) TX bytes:91867 (89.7 KiB)<br> eth0 Link encap:Ethernet HWaddr 00:26:B9:49:ED:45 <br> UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1<br> RX packets:264 errors:0 dropped:0 overruns:0 frame:0<br> TX packets:148 errors:0 dropped:0 overruns:0 carrier:0<br> collisions:0 txqueuelen:1000 <br> RX bytes:26203 (25.5 KiB) TX bytes:17895 (17.4 KiB)<br> Interrupt:226 Memory:d4000000-d4012800 <br> eth1 Link encap:Ethernet HWaddr 00:26:B9:49:ED:45 <br> UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1<br> RX packets:187 errors:0 dropped:0 overruns:0 frame:0<br> TX packets:117 errors:0 dropped:0 overruns:0 carrier:0<br> collisions:0 txqueuelen:1000 <br> RX bytes:18177 (17.7 KiB) TX bytes:14976 (14.6 KiB)<br> Interrupt:234 Memory:d6000000-d6012800 <br> eth4 Link encap:Ethernet HWaddr 00:26:B9:49:ED:45 <br> UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1<br> RX packets:22 errors:0 dropped:0 overruns:0 frame:0<br> TX packets:120 errors:0 dropped:0 overruns:0 carrier:0<br> collisions:0 txqueuelen:1000 <br> RX bytes:2728 (2.6 KiB) TX bytes:14800 (14.4 KiB)<br> Memory:ddbc0000-ddbe0000 <br> eth5 Link encap:Ethernet HWaddr 00:26:B9:49:ED:45 <br> UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1<br> RX packets:12 errors:0 dropped:0 overruns:0 frame:0<br> TX packets:118 errors:0 dropped:0 overruns:0 carrier:0<br> collisions:0 txqueuelen:1000 <br> RX bytes:1488 (1.4 KiB) TX bytes:14632 (14.2 KiB)<br> Memory:ddbe0000-ddc00000 <br> eth8 Link encap:Ethernet HWaddr 00:26:B9:49:ED:45 <br> UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1<br> RX packets:22 errors:0 dropped:0 overruns:0 frame:0<br> TX packets:119 errors:0 dropped:0 overruns:0 carrier:0<br> collisions:0 txqueuelen:1000 <br> RX bytes:2728 (2.6 KiB) TX bytes:14756 (14.4 KiB)<br> Memory:de7c0000-de7e0000 <br> eth9 Link encap:Ethernet HWaddr 00:26:B9:49:ED:45 <br> UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1<br> RX packets:12 errors:0 dropped:0 overruns:0 frame:0<br> TX packets:121 errors:0 dropped:0 overruns:0 carrier:0<br> collisions:0 txqueuelen:1000 <br> RX bytes:1488 (1.4 KiB) TX bytes:14808 (14.4 KiB)<br> Memory:de7e0000-de800000<br>
你可以发布configuration文件的债券接口和交换机连接到网卡？ 您必须确保所有NIC都configuration相同的聚合器ID。
确保您在交换机上也设置了一个ID，并将其中继线模式设置为“激活”。
http://studyhat.blogspot.com/2009/10/linux-nic-bonding.html
在上面的链接检查模式configuration在你结束哪种模式正在使用。