绑定：仅适用于下载

我想用模式4安装4个链接的绑定，但只有“下载/接收”与bondig一起工作。为传输系统select一条链路。

使用ifconfig

bond0 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 inet addr:ip Bcast:ip Mask:255.255.255.248 inet6 addr: fe80::92e2:baff:fe0f:76b4/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:239187413 errors:0 dropped:10944 overruns:0 frame:0 TX packets:536902370 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14688536197 (13.6 GiB) TX bytes:799521192901 (744.6 GiB) eth2 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:54969488 errors:0 dropped:0 overruns:0 frame:0 TX packets:2537 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3374778591 (3.1 GiB) TX bytes:314290 (306.9 KiB) eth3 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:64935805 errors:0 dropped:1 overruns:0 frame:0 TX packets:2532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3993499746 (3.7 GiB) TX bytes:313968 (306.6 KiB) eth4 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:57352105 errors:0 dropped:2 overruns:0 frame:0 TX packets:536894778 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3524236530 (3.2 GiB) TX bytes:799520265627 (744.6 GiB) eth5 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:61930025 errors:0 dropped:3 overruns:0 frame:0 TX packets:2540 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3796021948 (3.5 GiB) TX bytes:314274 (306.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:62 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5320 (5.1 KiB) TX bytes:5320 (5.1 KiB)

这些是我的configuration：

 DEVICE="eth2" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth3" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth4" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth5" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE=bond0 IPADDR=<ip> BROADCAST=<ip> NETWORK=<ip> GATEWAY=<ip> NETMASK=<ip> USERCTL=no BOOTPROTO=none ONBOOT=yes NM_CONTROLLED=no

cat / proc / net / bonding / bond0

 Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) Bonding Mode: IEEE 802.3ad Dynamic link aggregation Transmit Hash Policy: layer2 (0) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 802.3ad info LACP rate: slow Aggregator selection policy (ad_select): stable Active Aggregator Info: Aggregator ID: 1 Number of ports: 4 Actor Key: 17 Partner Key: 11 Partner Mac Address: 00:24:51:12:63:00 Slave Interface: eth2 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b4 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b5 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b6 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b7 Aggregator ID: 1 Slave queue ID: 0

/etc/modprobe.d/bonding.conf

 alias bond0 bonding options bond0 mode=4 miimon=100 updelay=200 #downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1

Linux的：

 Linux 3.0.0+ #1 SMP Fri Oct 26 07:55:47 EEST 2012 x86_64 x86_64 x86_64 GNU/Linux

我试过了：

downdelay = 200 xmit_hash_policy = layer3 + 4 lacp_rate = 1

 mode 6

在开始debugging绑定configuration之前，您是否validation了每个networking链接都可以自行工作？如果没有任何工作，当你把eth4（ ifdown eth4 ），那么很可能是你的接线问题。

另外，你应该先尝试一些更简单的键合模式。尝试balance-rr（ mode=0 ），看看你是否可以看到所有接口的stream量。也可以在/proc/net/bonding/bond0中查看configuration的当前状态。

你应该阅读这个文件： Linux绑定

http://wiki.mikrotik.com/wiki/Manual:Interface/Bonding说：

LACP根据哈希协议头信息平衡活动端口上的出站stream量，并接受来自任何活动端口的入站stream量。 […]散列的计算方式取决于transmit-hash-policy参数。

transmit-hash-policy：layer-2 – 使用硬件MAC地址的异或来生成散列。这个algorithm将把所有的stream量都放到一个特定的networking节点上。

所以，如果你从bond0只发送到networking中的单个目的地，也就是说，对于一个单一的 MAC地址，所有的帧只从你的一个端口发出。这是一个预期的行为。如果你要转移到其他MAC地址，那么散列algorithm可能会从你的4个端口中select其他3个端口中的一个（机会是75％）。这是为了确保帧的传送顺序与发送顺序相同。

PS：如果您的传输通过IP网关，这也算作单MAC传输。相当常见的情况。