我们使用dd从IBM PS-703（P系列，即Power-PC）BladeCenter中捕获磁盘映像。 在救援模式。 图像是RedHat 5.11。 目标是获得服务器的备份映像，并将该映像映射到另外两台服务器上，一个生产，一个备份。
我们使用IBM PS-701（P系列）服务器上的映像构build了一台新的服务器。 这将是新的生产机器。 在救援模式下使用dd恢复图像。
PS-701引导并运行安装的备份映像。 但是，没有以lspci报告的以太网接口。 lsdev不可用，因为我们的公司图像在安装时会阻止它。
原来的PS-703报告了两个Broadcom NetXtreme以太网适配器的存在。 如上所述，PS-701没有看到适配器。 IBM Fix Central的最新更新表明，701具有QLogic适配器，但在另一个701上运行lspci则显示有两个IBM eHEA适配器。 我们不确定哪一个是正确的。 新机器显示你不能通过它的AMM闪光。
谁能告诉我们如何确定701的以太网适配器的types？ 另外，你能告诉我们安装哪个驱动程序？ 以及如何使以太网可见？
迈克尔汉普顿每个请求添加dmesg输出 。
从正在工作的类似机器：
Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack IBM eHEA ethernet device driver (Release EHEA_0092-05) ehea: eth0: Jumbo frames are enabled ehea: eth0 -> logical port id #1 ehea: eth1: Jumbo frames are enabled ehea: eth1 -> logical port id #2 ehea: eth0: Physical port up ehea: External switch port is backup port 8021q: adding VLAN 0 to HW filter on device eth0 并从非工作机器：
Using pSeries machine description Page orders: linear mapping = 24, virtual = 16, io = 12 Found initrd at 0xc000000002b80000:0xc000000002f40800 Partition configured for 16 cpus. Starting Linux PPC64 #1 SMP Fri May 1 10:40:05 EDT 2015 ----------------------------------------------------- ppc64_pft_size = 0x1d physicalMemorySize = 0x7a0000000 ppc64_caches.dcache_line_size = 0x80 ppc64_caches.icache_line_size = 0x80 htab_address = 0x(null) htab_hash_mask = 0x3fffff ----------------------------------------------------- Linux version 2.6.18-406.el5 ([email protected].redhat.com) (gcc v ersion 4.1.2 20080704 (Red Hat 4.1.2-55)) #1 SMP Fri May 1 10:40:05 EDT 2015 [boot]0012 Setup Arch Node 0 Memory: 0x0-0x7a0000000 EEH: PCI Enhanced I/O Error Handling Enabled PPC64 nvram contains 15360 bytes Using dedicated idle loop On node 0 totalpages: 499712 DMA zone: 499712 pages, LIFO batch:1 [boot]0015 Setup Done Built 1 zonelists. Total pages: 499712 Kernel command line: root=/dev/VolGroup00/LogVol00 ro console=hvc0 rhgb quiet [boot]0020 XICS Init xics: no ISA interrupt controller [boot]0021 XICS Done PID hash table entries: 4096 (order: 12, 32768 bytes) time_init: decrementer frequency = 512.000000 MHz time_init: processor frequency = 3000.000000 MHz Console: colour dummy device 80x25 Dentry cache hash table entries: 4194304 (order: 9, 33554432 bytes) Inode-cache hash table entries: 2097152 (order: 8, 16777216 bytes) freeing bootmem node 0 Memory: 31873344k/31981568k available (5056k kernel code, 108224k reserved, 1344 k data, 1257k bss, 320k init) Calibrating delay loop... 1021.95 BogoMIPS (lpj=510976) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 4096 Processor 1 found. Processor 2 found. Processor 3 found. Processor 4 found. Processor 5 found. Processor 6 found. Processor 7 found. Processor 8 found. Processor 9 found. Processor 10 found. Processor 11 found. Processor 12 found. Processor 13 found. Processor 14 found. Processor 15 found. Brought up 16 CPUs Node 0 CPUs: 0-15 sizeof(vma)=176 bytes sizeof(page)=56 bytes sizeof(inode)=560 bytes sizeof(dentry)=216 bytes sizeof(ext3inode)=760 bytes sizeof(buffer_head)=96 bytes sizeof(skbuff)=248 bytes migration_cost=0,691 checking if image is initramfs... it is Freeing initrd memory: 3842k freed NET: Registered protocol family 16 PCI: Probing PCI hardware IOMMU table initialized, virtual merging enabled mapping IO 3dffc01f0000 -> d0000800000f0000, size: 10000 mapping IO 3dffc02f0000 -> d0000800001f0000, size: 10000 PCI: Probing PCI hardware done Registering pmac pic with sysfs... No pciex nodes found No pcix nodes found usbcore: registered new driver usbfs usbcore: registered new driver hub NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default NET: Registered protocol family 2 IP route cache hash table entries: 1048576 (order: 7, 8388608 bytes) TCP established hash table entries: 1048576 (order: 8, 16777216 bytes) TCP bind hash table entries: 65536 (order: 4, 1048576 bytes) TCP: Hash tables configured (established 1048576 bind 65536) TCP reno registered vio_bus_init: processing c00000079fffcd98 vio_bus_init: processing c00000079fffcf50 vio_bus_init: processing c00000079fffd088 vio_bus_init: processing c00000079fffd1e0 vio_bus_init: processing c00000079fffd338 IBM eBus Device Driver scan-log-dump not implemented on this system RTAS daemon started RTAS: event: 19, Type: Platform Error, Severity: 2 audit: initializing netlink socket (disabled) type=2000 audit(1440014763.530:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 8192 (order 0, 65536 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API alg: No test for crc32c (crc32c-generic) ksign: Installing public key data Loading keyring - Added public key D8CAB7B6B14A884 - User ID: Red Hat, Inc. (Kernel Module GPG key) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 rpaphp: RPA HOT Plug PCI Controller Driver version: 0.1 vio_register_driver: driver hvc_console registering HVSI: registered 0 devices Generic RTC Driver v1.07 Linux agpgart interface v0.101 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled brd: module loaded Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide-floppy driver 0.99.newide usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Initalizing network drop monitor service Freeing unused kernel memory: 320k freed PCI: Enabling device: (0001:00:01.2), cmd 142 ehci_hcd 0001:00:01.2: EHCI Host Controller ehci_hcd 0001:00:01.2: new USB bus registered, assigned bus number 1 ehci_hcd 0001:00:01.2: irq 307, io mem 0x3b00ffffd000 ehci_hcd 0001:00:01.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd 0001:00:01.0: OHCI Host Controller ohci_hcd 0001:00:01.0: new USB bus registered, assigned bus number 2 ohci_hcd 0001:00:01.0: irq 305, io mem 0x3b00ffffe000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected ohci_hcd 0001:00:01.1: OHCI Host Controller ohci_hcd 0001:00:01.1: new USB bus registered, assigned bus number 3 ohci_hcd 0001:00:01.1: irq 306, io mem 0x3b00fffff000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 SCSI subsystem initialized libata version 3.00 loaded. ipr: IBM Power RAID SCSI Device Driver version: 2.5.3 (March 10, 2012) ipr 0000:00:01.0: Found IOA with IRQ: 289 ipr 0000:00:01.0: Starting IOA initialization sequence. ipr 0000:00:01.0: Adapter firmware version: 04200015 ipr 0000:00:01.0: IOA initialized. scsi0 : IBM 57D0 Storage Adapter Vendor: IBM-ESXS Model: ST9600204SS Rev: B541 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 1172123568 512-byte hdwr sectors (600127 MB) sda: Write Protect is off sda: Mode Sense: df 00 10 08 SCSI device sda: drive cache: write through w/ FUA SCSI device sda: 1172123568 512-byte hdwr sectors (600127 MB) sda: Write Protect is off sda: Mode Sense: df 00 10 08 SCSI device sda: drive cache: write through w/ FUA sda: sda1 sda2 sda3 sd 0:2:0:0: Attached scsi disk sda Vendor: IBM Model: VSBPD1BK SAS Rev: 01 Type: Enclosure ANSI SCSI revision: 02 scsi: unknown device type 31 Vendor: IBM Model: 57D0001SISIOA Rev: 0150 Type: Unknown ANSI SCSI revision: 00 device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.11.6-ioctl (2011-02-18) initialised: [email protected] device-mapper: dm-raid45: initialized v0.2594l kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks type=1404 audit(1440014784.958:2): selinux=0 auid=4294967295 ses=4294967295 sd 0:2:0:0: Attached scsi generic sg0 type 0 scsi 0:8:0:0: Attached scsi generic sg1 type 13 scsi 0:255:255:255: Attached scsi generic sg2 type 31 lp: driver loaded but no devices found md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. device-mapper: multipath: version 1.0.6 loaded loop: loaded (max 8 devices) EXT3 FS on dm-0, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 50102144k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across :50102144k Loading iSCSI transport class v2.0-871. 802.1Q VLAN Support v1.8 Ben Greear <[email protected]> All bugs added by David S. Miller <[email protected]> libcxgbi:libcxgbi_init_module: tag itt 0x1fff, 13 bits, age 0xf, 4 bits. libcxgbi:ddp_setup_host_page_size: system PAGE 65536, ddp idx 3. Chelsio T3 iSCSI Driver cxgb3i v2.0.0 (Jun. 2010) iscsi: registered transport (cxgb3i) IPv6: Loaded, but administratively disabled, reboot required to enable cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.12 (June 29, 2012) Broadcom NetXtreme II iSCSI Driver bnx2i v2.7.2.2 (Jun 18, 2012) iscsi: registered transport (bnx2i) iscsi: registered transport (tcp) iscsi: registered transport (iser) iscsi: registered transport (be2iscsi) ip6_tables: (C) 2000-2006 Netfilter Core Team ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack Bluetooth: Core ver 2.10 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 Bluetooth: HIDP (Human Interface Emulation) ver 1.1 usb 1-1: new high speed USB device using ehci_hcd and address 2 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 2 ports detected usb 1-1.2: new high speed USB device using ehci_hcd and address 3 usb 1-1.2: configuration #1 chosen from 1 choice hub 1-1.2:1.0: USB hub found hub 1-1.2:1.0: 4 ports detected usb 1-1.2.3: new high speed USB device using ehci_hcd and address 4 usb 1-1.2.3: configuration #1 chosen from 1 choice Initializing USB Mass Storage driver... scsi1 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usb-storage USB Mass Storage support registered. Vendor: MATSHITA Model: UJDA780 DVD/CDRW Rev: CA22 Type: CD-ROM ANSI SCSI revision: 00 scsi 1:0:0:0: Attached scsi generic sg3 type 5 usb-storage: device scan complete usb 1-1.2.3: reset high speed USB device using ehci_hcd and address 4 sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 usb 1-1: USB disconnect, address 2 usb 1-1.2: USB disconnect, address 3 usb 1-1.2.3: USB disconnect, address 4 usb 1-1: new high speed USB device using ehci_hcd and address 5 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 2 ports detected usb 1-1.2: new high speed USB device using ehci_hcd and address 6 usb 1-1.2: configuration #1 chosen from 1 choice hub 1-1.2:1.0: USB hub found hub 1-1.2:1.0: 4 ports detected usb 1-1.2.3: new high speed USB device using ehci_hcd and address 7 usb 1-1.2.3: configuration #1 chosen from 1 choice scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 7 usb-storage: waiting for device to settle before scanning Vendor: MATSHITA Model: UJDA780 DVD/CDRW Rev: CA22 Type: CD-ROM ANSI SCSI revision: 00 sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray sr 2:0:0:0: Attached scsi CD-ROM sr0 sr 2:0:0:0: Attached scsi generic sg3 type 5 usb-storage: device scan complete ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A
你可以发布dmesg输出吗？
一般来说，解决这个问题的最好方法是查看机箱pipe理模块。 它应该有一个选项来枚举刀片内的设备。
（我会评论，但低代表）
编辑：我不再有一个有效的IBM支持权利，所以我不能直接链接你，但它看起来像你有eHEA模型。 应该有驱动程序挂在PS701支持页面上。 另外，还有一个开源的驱动你可以在这里试试： http : //sourceforge.net/projects/ibmehcad/
我仍然鼓励你检查刀片的完整硬件清单的CMM，因为我只是猜测你的其他输出的基础上。 另一个select是尝试使用lsvpd，如果您安装IBM支持/服务工具（或运行AIX），则只能获得这个lsvpd。